C-IS-0404S Модуль CIB без крышки, 4×AI/DI, 4×DO, PWM, H-мост

The C-IS-0404S module on the CIB Common Installation Bus® with 4x AI / DI and 4x DO and is built-in. It contains four binary outputs that can be used (in pairs DO1 with DO2 and DO3 with DO4) as 'H bridges' for controlled polarity reversal or as PWM outputs of the open collector type eg for control of model actuators (only with external power supply), or as common transistor outputs 24 VDC 50 mA. It contains four universal inputs configurable in pairs (DI / AI1 with DI / AI2 and DI / AI3 with DI / AI4) either as binary allowing connection of a potential-free contact against a common GND conductor or as analog for direct connection of passive resistance sensors Pt1000, Ni1000, NTC 12k , KTY 81-121 (measured resistance value is converted in the module directly to a numerical temperature value), or general resistance measurement in the range of 0–100 kΩ or DC voltage in the range of 0–2 V. The TXN 143 14 module is in a shrink tube and is equipped with terminal blocks with tongue terminals. The TXN 143 14.01 module is not protected by a tube or does not contain terminal blocks, all signals are routed to the socket strips, a built-in connection is assumed here by sliding the module onto the plugs of the expansion board.

DI
DI/AI	4x DI/AI
DO
AI
AO
COM
SENSOR

COM - System buses
CIB - Common Installation Bus (R): Installation I/O bus	1x CIB slave
DI - Organization of binary inputs
Total number of binary inputs	2
Number of groups of binary inputs	1
Organization of binary inputs into groups	2x DI (AI1 - AI2)
DI - Parameters of binary inputs DC (group A)
Parameters valid for inputs on the terminals	AI1 - AI2
Number of inputs in group	2
Common wire	GND - module ground
Combined input type	DI / AI - measurement of resistance sensors, sensing of potential-free contacts and balanced loops
Galvanic isolation of inputs from internal/peripheral circuits	No
Max. measuring voltage on the connected contact	3,3 V DC
Internal input resistance	2 kΩ
Max. resistance for closed contact, log. 1	< 0,5 kΩ
Min. resistance for open contact, log. 0	> 4,2 kΩ
Balanced resistance input	2× 1k1 (tamper/0/1/tamper)
DO/RO - Organization of binary outputs
Total number of binary outputs	5
Number of binary output groups	2
Organization of binary outputs into groups	4x (DO1 - DO4) 1x (DO5)
DO - Parameters of binary transistor outputs (group A)
Parameters valid for the terminals	DO1-DO4
Number of outputs in group	4
Organization of transistor outputs into groups	3 (DO1-DO3)
Output type	MOSFET (High-side switch)
Galvanic separation from internal circuits	No
Galvanic isolation of the outputs from CIB	No
Diagnostics	No
Switching voltage	9 - 30 V DC
Group current	160 mА
Output current	160 mA
Switching time	typ. 40 μs (12-24V, 60-160mA)
Opening time	typ. 70 μs (12-24V, 60-160mA)
Residual current	max. 10 μA
Short circuit protection	Yes
Special functions (A)	PWM
Operating frequency	100 Hz ÷ 2 kHz
DO - Parameters of binary transistor outputs (group B)
Parameters valid for the terminals	DO5
Common group conductor	COM2
Output type	transistor output
Galvanic separation from internal circuits	Yes
Switching voltage	0 - 48V DC
Switching current, output load	80 mA (160mA @ 25˚C)
Residual current	5 μA max.
Short circuit protection	No
Special functions	PWM
Operating frequency	100 Hz ÷ 2 kHz
AI - Organization of analog inputs
Total number of analog inputs	2
Number of inputs per group	2
Number of analog input groups	1
Organization of analog inputs into groups	2x (AI1, AI2)
Input type	AI / DI - combined
Common wire	GND terminal
Galvanic separation from internal circuits	No
Diagnostics	overload signaling in status word
Digital resolution	10 bit
AI - Analog Input Ranges (Group A)
Parameters valid for inputs on the terminals	AI1, AI2
Passive sensor	NTC Thermistor 12k / 25 °C (-40 to + 125 °C)
Power supply
Supply voltage, tolerances	24/27 V DC from CIB bus
Auxiliary power supply - voltage	Supply output +22V OUT: U0 = CIB bus voltage -1 V, Iout max = 60mA, internal resistance R < 88 Ω
Typical power input	0,5 W
Maximum power input	2,2 W
Module thermal/power loss	0,4 W
Power supply from CIB - typical current consumption (mA)	20 mA
Power supply from CIB - maximum current consumption (mA)	80 mA
Description of power supply	Difference between typical and maximum power input is given by possible load of CIB buses and number of switched outputs and CPU load
Thermal/power loss of the module max.	0.65W (at maximum consumption of outputs powered by auxiliary voltage +22V OUT)
Size and weight
Weight approx.	7 g
Product dimensions (width x height x depth)	55 × 26 × 16 mm
Operating conditions, product standards
Product standard	ČSN EN 60730-1 ed.4 :2017 (EN 60730-1:2016) -Automatic electronic control device (for household and similar purposes)
Protection class of electrical object	III, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP10B
Operating areas	Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution	1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation	II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device	In the installation box, under the cover
Working position	Any
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	0 ° C to + 55 ° C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 ° C to + 85 ° C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	ČSN EN 55022 ed2:2007 (mod CISPR22:2005)
Electromagnetic compatibility / Immunity	min. according to ČSN EN 60730-1 ed.2: 2001
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	Модуль упакован в антистатический пакет. Эта документация также является частью пакета. Внешняя упаковка осуществляется в соответствии с объемом заказа и способом транспортировки в транспортной упаковке, снабженной этикетками и другими данными, необходимыми для транспортировки. Продукт не должен подвергаться воздействию прямых погодных условий во время транспортировки и хранения. Соложение продукта разрешено только в чистых помещениях. без токопроводящей пыли, агрессивных газов и паров. Наиболее подходящая температура хранения - 20 ° C.
Installation
Assembly description	The module C-DM-0001B-SL is mounted in arbitrary positioninto instalation box under a lid or under device located in box.
Connection
Connection of power and system communication	terminal block with spring terminal 0.15-0.5 mm2, push-in
Connection of inputs / outputs	terminal block with spring clamp 0.15-0.5 mm2, push-in
Connection description	An example of module connection is shown in the following figure.
Module operation
Module configuration	The module is operated, set up and diagnosed from the Mosaic development environment.
Commissioning	The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module.
Module diagnostics	The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment.
Maintenance
Description	The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.