C-IT-0908S-PNP Модуль CIB, 6×DI, 2×AI/DI, драйвер 8×PNP LED

The C-IT-0908S module is intended for the CIB Common Installaton Bus® for the connection of sensing analog or binary signals (sensing potential-free contacts) and controlling binary outputs, including for driving LEDs. Inputs DI1 to DI6 can only be set as binary. They also work in balanced input mode. Inputs DI / AI7 to DI / AI8 can be set as binary or analog. Input AI9 can only be set as analog. Eight binary outputs are designed to drive LEDs connected in a group with common cathodes or common anodes (version with * .01 number),

DI	6x DI
DI/AI	2x DI/AI
DO	8x DO
AI	1x AI
AO
COM	1x CIB
SENSOR

COM - System buses
CIB - Common Installation Bus (R): Installation I/O bus	1x CIB slave
DI - Parameters of binary inputs DC (group A)
Parameters valid for inputs on the terminals	AI1/DI1, AI/DI2
Number of inputs in group	2
Common wire	GND - module ground
Combined input type	DI/AI Active, for sensing potential-free contacts and measuring resistance sensors
Galvanic isolation of inputs from internal/peripheral circuits	No
Diagnostics	signaling of excited input in Mosaic
Input voltage	3.3 V from internal source
Input current at log. 1 (typ.)	3,3 mA
Delay from log. 0 to log. 1	10 ms
Delay from log. 1 to log. 0	300 ms
The minimum width of the captured pulse	10 ms
AI - Organization of analog inputs
Total number of analog inputs	2
Common wire	Plus
Galvanic separation from internal circuits	No
External power supply	No
Digital resolution	12 bit
Converter type	Approximation
conversion time	500 μs
AI - Analog Input Ranges (Group A)
Parameters valid for inputs on the terminals	AI1/DI1, AI/DI2
Passive sensor	NTC Thermistor 12k / 25 °C (-40 to + 125 °C)
Input impedance in signal range RTD	> 1 kΩ
Resistance measurement error - maximum error at 25 ° C	± 2% of full scale
Resistance measurement error - temperature coefficient	± 0,1% of full scale
Resistance measurement error - non-linearity	± 0.2% of full scale
Resistance measurement error - repeatability at steady conditions	0.5% of full scale
Detection of disconnected sensor	No
Input parameters for connecting a light sensor
Number of inputs	1
Galvanic isolation	No
Lighting - Sensor type	Photodiode BPW21
Lighting - Conversion time	500 μs
Lighting - Measuring range	0 lx ÷ 50000 lx
Lighting - Measurement error	<5% of range
Lighting - Temperature coefficient	± 0.1% of full scale / ° C
Lighting - Linearity of measurements	± 0.2% of full scale
Lighting - Repeatability under steady state conditions	0.5% of full scale
Parameters of IR receiver / transmitter inputs / outputs
Number of inputs for connecting the IR receiver demodulator	1
Demodulator power supply	3,3 V
Galvanic separation from internal circuits	No
Demodulator carrier frequency	36 kHz
Output parameters for IR transmitter connection
Number of outputs	1
Transmitter power supply	3,3 V
Short circuit protection	No
Galvanic separation from internal circuits	No
IR transmitter	IR LED (IFMAX = 100mA) + resistor according to IF
IR transmitter, example	IR LED UF = 1.2V, IF = 20mA → R = 100Ω
Power supply
Supply voltage, tolerances	24/27 V DC from CIB bus
Maximum power input	< 0,5 W
Power supply from CIB - maximum current consumption (mA)	25 mA
Power supply from CIB - internal protection	No
Size and weight
Weight approx.	7 g
Product dimensions (width x height x depth)	55 x 32 x 13 mm
Operating conditions, product standards
Product standard	ČSN EN 60730-1 ed. 2:2001 (mod IEC 60730-1:1999)
Protection class of electrical object	I, according to ČSN EN 61140: 2003 (idt IEC 61140: 2001)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP10B
Operating areas	Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution	1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation	II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device	In the installation box, under the cover
Working position	Any
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	-10 °C to + 55 °C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	B, according to EN 55022: 1999 (mod CISPR22: 1997)
Electromagnetic compatibility / Immunity	min. according to ČSN EN 60730-1 ed.2: 2001
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	Модуль упакован в антистатический пакет. Эта документация также является частью пакета. Внешняя упаковка осуществляется в соответствии с объемом заказа и способом транспортировки в транспортной упаковке, снабженной этикетками и другими данными, необходимыми для транспортировки. Продукт не должен подвергаться воздействию прямых погодных условий во время транспортировки и хранения. Соложение продукта разрешено только в чистых помещениях. без токопроводящей пыли, агрессивных газов и паров. Наиболее подходящая температура хранения - 20 ° C.
Installation
Assembly description	The C-RI-0401S module can be mounted in any position in the installation box or under the device cover. Installation of the assembly (basic module and possibly peripheral modules) is performed according to TXV 004 13.
Connection
Connection of power and system communication	Ribbon flat conductors 0.15 / 0.5 mm2
Module connection	The combined module is implemented as a CIB bus module, which provides communication. The power supply of the module is from an external source. The CIB bus can have any topology and branching up to a distance of 500 m and up to 32 units on one CIB branch. The CIB bus master is the FOXTROT basic unit or module, for example MI2-02M. Further information can be found in the manual Peripheral modules on the CIB TXV 004 13. An example of module connection is shown in the following figure.
Module operation
Commissioning	The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module.
Maintenance
Description	The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.