C-RQ-0600S Модуль CIB для датчиков температуры, влажности, движения и CO

The C-RQ-0600S module is the basis for several variants of modules designed for the connection of a humidity and temperature sensor, or a CO2 sensor, or an infrared motion sensor and universal analog or binary signals. Universal AI / DI inputs can be set to binary or analog with the possibility of measuring temperature sensors: support sensors PT1000, Ni1000, or a sensor with a NTC12k or KTY81-121 thermistor against a common GND wire. For another type of resistance sensor, a resistance measurement range of 0 to 160 kΩ can be selected, but the conversion to temperature and linearization must be performed in the user program. The binary signals are connected to the inputs only as a potential-free contact against the common GND conductor. The binary input can also operate in balanced input mode.

DI
DI/AI	2x DI/AI
DO
AI
AO
COM	1x CIB slave
SENSOR

COM - System buses
CIB - Common Installation Bus (R): Installation I/O bus	1x CIB slave
AI - Analog Input Ranges (Group A)
Parameters valid for inputs on the terminals	DI/AI1, DI/AI2
Passive sensor	NTC Thermistor 12k / 25 °C (-40 to + 125 °C)
DI: Voltage-free contact	0 when> 1.5 kOhm, 1 when <0.5 kOhm
DI: Balanced resistance input	2x 1k1 (tamper/0/1/tamper)
Resistance measurement error - maximum error at 25 ° C	± 0.5% of full scale
Power supply
Supply voltage, tolerances	24/27 V DC from CIB bus
Power supply from CIB - typical current consumption (mA)	15 mA
Power supply from CIB - maximum current consumption (mA)	20 mA
Power supply from CIB - internal protection	Yes, returnable fuse
Size and weight
Weight approx.	7 g
Product dimensions (width x height x depth)	55 × 27 × 20 mm
Operating conditions, product standards
Product standard	ČSN EN 60730-1 ed. 2:2001 (mod IEC 60730-1:1999)
Protection class of electrical object	III, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP10B
Operating areas	Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution	1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation	II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device	In the installation box, under the cover
Working position	Any
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	0 ° C to + 70 ° C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 ° C to + 85 ° C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	ČSN EN 55022 ed2:2007 (mod CISPR22:2005)
Electromagnetic compatibility / Immunity	min. according to ČSN EN 60730-1 ed.2: 2001
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	The module is packed in a paper box. This documentation is also part of the package. The outer packaging is carried out according to the scope of the order and the method of transport in a transport package provided with labels and other data necessary for transport. The product must not be exposed to direct weather conditions during transport and storage. Malting of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C
Installation
Assembly description	The module C-DM-0001B-SL is mounted in arbitrary positioninto instalation box under a lid or under device located in box.
Connection
Connection description	An example of module connection is shown in the following figure.
Connection of power and system communication	terminal block with spring terminal 0.15-0.5 mm2, push-in
Module operation
Commissioning	The module is operated, set and diagnosed by the MOSAIC or FoxTool programming environment. Further information can be found in the manual Peripheral modules on the CIB TXV 004 13.
Module diagnostics	The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment.
Maintenance
Description	The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.