C-IS-0504M Модуль CIB, 3×AI/DI, 3×RO, PWM, 2×AI для измерения сопротивления

C-IS-0504M is a module on the CIB bus with a total of 9 inputs / outputs in combination 3x combined AI / DI input for sensing contacts and measuring resistance thermometers, 2x analog input specialized for measuring AC resistances (excluding long-term electrolysis in a humid environment - icing, precipitation, level probes) 1x semiconductor output with pulse width modulation (PWM from 100 Hz to 2 kHz and load capacity max. 4W) 2x relay output 5 A, 1x relay output 16A, with resistance to inrush current up to 80 A The individual relay outputs have a status LED indication and can be manually controlled locally by buttons on the module panel. Use Inputs and outputs can be used as general AI / DI and RO Specialized use: Controlled heating supply and measurement of precipitation detector S-RS-01I, Heating supply and measurement of icing sensors with a nominal voltage of 24 V. Up to 2 probes for level measurement, eg for limit monitoring of water in the tank.

DI
DI/AI	3x DI/AI
DO	1x RO 16A 2x RO 3A 1x DO (PWM)
AI	2x AI (AC resistance measurement <1MΩ)
AO
COM	1x CIB slave
SENSOR

RO - Parameters of binary relay outputs (group A)
Number of relay outputs	8
Number of output groups	3
Number of outputs in group	1
Organization of relay outputs into groups	Independently
Output type	electromechanical relay, unprotected output
Contact type	NO / NC changeover contact
Diagnose	Alarm signaling on panel module
Switching current	16 A max. NO/10 A max NC, 100 mA min.
Switching voltage	300 V max., 5 V min.
Short-term output overload - inrush	80 A max. (20 ms max.)
Contact closing time	typ. 15 ms
Contact opening time	typ. 5ms
Mechanical life	min. 5,000,000 cycles
Short-circuit protection	No
Treatment of inductive load	External RC element, varistor (AC), diode (DC)
Insulation voltage between outputs and internal circuits	3750 V AC
Notice!	An insulation voltage of 3750V AC is not guaranteed between the contacts on the common terminal block
Power supply
Power supply from CIB - voltage	24/27 V DC
Auxiliary power supply - voltage	24 V DC, +- 10%
Typical power input	4 W
Maximum power input	4,5 W
Module thermal/power loss	4 W
Maximum current consumption (mA)	200 mA
Power supply from CIB - maximum current consumption (mA)	160 mA
Galvanic separation of power supply from internal circuits	No
Size and weight
Weight approx.	350 g
Product dimensions (width x height x depth)	105 x 92 x 58 mm
Module width in multiples of M (17.5 mm)	6M
Module width	105 mm
Module height	92 mm
Module depth	58 mm
Operating conditions, product standards
Product standard	ČSN EN 61131-2 ed.2: 2008 (IEC 61131-2: 2007) и ČSN EN 60730-1 ed.4: 2017 (EN 60730-1: 2016)
Protection class of electrical object	I, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP20
Operating areas	Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution	1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation	II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device	Module on DIN rail
Working position	Vertical
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	-10 °C to + 55 °C
Operating temperature maximum (° C)	+55°C
Operating temperature minimum (° C)	-10°C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	B, according to EN 55022: 1999 (mod CISPR22: 1997)
Emmisions - note	In premises where the use of radio and television receivers can be expected to be used a distance of 10 m from these devices may cause radio interference. In such a case, the user may be required to take appropriate action.
Electromagnetic compatibility / Immunity	min. according to ČSN EN 60730-1 ed.2: 2001
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	The module is packed in a paper box. This documentation is also part of the package. The outer packaging is carried out according to the scope of the order and the method of transport in a transport package provided with labels and other data necessary for transport. The product must not be exposed to direct weather conditions during transport and storage. Malting of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C
Installation
Attention!	The device may contain parts with dangerous voltages, covers being removed, or cabling manipulated, or disconnect the appropriate circuits or turn off the power !.
Connection
Connection of power and system communication	connector with 2.5 mm2 screw terminal
Connection of inputs / outputs	connector with screw terminal 2.5 mm2
Module operation
Module configuration	LEDs on the front of the module are used to diagnose the condition. To set the button on the module as described in the diagrams section
Maintenance
Description	The module does not require any maintenance under general installation conditions.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.