C-IT-0200R-Logus Белый датчик температуры CIB для помещений, 2 датчика температуры (внутренний и внешний), купить на Prom.ua

Производитель	Teco
Страна производитель	Чехия
Состояние	Новое

Производитель

Teco

Страна производитель

Чехия

Состояние

Новое

AI	1x AI (NTC12k, 0-100kΩ)
COM	1x CIB slave
SENSOR	1x Temperature
Колір	white

1x AI (NTC12k, 0-100kΩ)

COM

1x CIB slave

SENSOR

1x Temperature

Колір

white

COM - System buses
CIB - Common Installation Bus (R): Installation I/O bus	1x CIB slave
AI - Analog Input Ranges (Group C)
Parameters valid for inputs on the terminals	+IN, -IN
Passive sensor	NTC Thermistor 12k / 25 °C (-40 to + 125 °C)
Resistance measurement error - maximum error at 25 ° C	± 0.5% of full scale
Parameter des Temperatursensors
Temperature - Measurement range	0°C ÷ 50°C
Temperature - Resolution	0,1 °C
Temperature - Measurement accuracy	typ. ±0,5 °C
Power supply
Supply voltage, tolerances	24/27 V DC from CIB bus
Typical power input	0,3 W
Maximum power input	< 0,5 W
Galvanic separation of power supply from internal circuits	No
Internal protection	Yes, PTC reversible fuse
Size and weight
Weight approx.	75 g
Product dimensions (width x height x depth)	56 x 26 x 16 mm
Operating conditions, product standards
Product standard	ČSN EN 60730-1 ed. 2:2001 (mod IEC 60730-1:1999)
Protection class of electrical object	III, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP10B
Operating areas	Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution	1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation	II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device	In the installation box on the wall
Working position	Any
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	0 °C to + 55 °C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	B, according to EN 55022: 1999 (mod CISPR22: 1997)
Electromagnetic compatibility / Immunity	min. according to ČSN EN 60730-1 ed.2: 2001
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	The module is packed in a paper box. This documentation is also part of the package. The outer packaging is carried out according to the scope of the order and the method of transport in a transport package provided with labels and other data necessary for transport. The product must not be exposed to direct weather conditions during transport and storage. Malting of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C
Installation
Assembly description	Indoor wall mounting
Connection
Connection description	The module is implemented as a standard unit on a two-wire CIB bus, which ensures communication and power supply of the entire sensor. The bus wires are connected to the wires that are routed on the tube module (see Fig. 2). The CIB bus can have any topology and branching up to a distance of 500 m and up to 32 units on one CIB branch. The CIB bus master is the basic PLC unit TECOMAT FOXTROT or an external CIB bus master, eg the CF-1141 module. Further information can be found in the manual Peripheral modules on the CIB TXV 004 13. Assembly C-IT-0200R-Design: 1. Tube module 2. Temperature sensor in selected interior design
Connection of power and system communication	Loose wires in the connector / 0.15-0.5 mm2
Module connection	Assembly and installation instructions C-IT-0200R-Design: 1. Connect the module to the CIB bus. 2. Connect an external sensor (if used) to the appropriate wires of the tube module. 3. Slide the temperature sensor connector onto the tips of the tubing module. 4. Insert the tube module into the installation box. Be careful not to disconnect the temperature sensor connector from the tube module. 5. Attach the temperature sensor design to the installation box
Module operation
Module configuration	The module is operated, set up and diagnosed from the Mosaic development environment.
Commissioning	The module is ready for operation after connecting the CIB supply voltage. HW address of the relevant module is indicated on the type plate.
Maintenance
Description	The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.

COM - System buses

CIB - Common Installation Bus (R): Installation I/O bus

1x CIB slave

AI - Analog Input Ranges (Group C)

Parameters valid for inputs on the terminals

+IN, -IN

Passive sensor

NTC Thermistor 12k / 25 °C (-40 to + 125 °C)

Resistance measurement error - maximum error at 25 ° C

± 0.5% of full scale

Parameter des Temperatursensors

Temperature - Measurement range

0°C ÷ 50°C

Temperature - Resolution

0,1 °C

Temperature - Measurement accuracy

typ. ±0,5 °C

Power supply

Supply voltage, tolerances

24/27 V DC from CIB bus

Typical power input

0,3 W

Maximum power input

< 0,5 W

Galvanic separation of power supply from internal circuits

Internal protection

Yes, PTC reversible fuse

Size and weight

Weight approx.

75 g

Product dimensions (width x height x depth)

56 x 26 x 16 mm

Operating conditions, product standards

Product standard

ČSN EN 60730-1 ed. 2:2001 (mod IEC 60730-1:1999)

Protection class of electrical object

III, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)

IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)

IP10B

Operating areas

Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)

Degree of pollution

1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)

Overvoltage category installation

II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)

Type of device

In the installation box on the wall

Working position

Any

Type of operation (operating frequency)

Continuous

Ambient operating temperatures

0 °C to + 55 °C

Operating relative humidity

from 10 % up to 95 % without condensation

Operating atmospheric pressure

min. 70 kPa (<3,000 m above sea level)

Storage temperatures

–25 °C to +70 °C

Electromagnetic compatibility, Mechanical endurance

Electromagnetic compatibility / Emission

B, according to EN 55022: 1999 (mod CISPR22: 1997)

Electromagnetic compatibility / Immunity

min. according to ČSN EN 60730-1 ed.2: 2001

Sinusoidal vibration endurance

10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)

Packaginng, transportation, storage

Description

The module is packed in a paper box. This documentation is also part of the package. The outer packaging is carried out according to the scope of the order and the method of transport in a transport package provided with labels and other data necessary for transport. The product must not be exposed to direct weather conditions during transport and storage. Malting of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C

Installation

Assembly description

Indoor wall mounting

Connection

Connection description

The module is implemented as a standard unit on a two-wire CIB bus, which ensures communication and power supply of the entire sensor. The bus wires are connected to the wires that are routed on the tube module (see Fig. 2). The CIB bus can have any topology and branching up to a distance of 500 m and up to 32 units on one CIB branch. The CIB bus master is the basic PLC unit TECOMAT FOXTROT or an external CIB bus master, eg the CF-1141 module. Further information can be found in the manual Peripheral modules on the CIB TXV 004 13. Assembly C-IT-0200R-Design: 1. Tube module 2. Temperature sensor in selected interior design

Connection of power and system communication

Loose wires in the connector / 0.15-0.5 mm2

Module connection

Assembly and installation instructions C-IT-0200R-Design: 1. Connect the module to the CIB bus. 2. Connect an external sensor (if used) to the appropriate wires of the tube module. 3. Slide the temperature sensor connector onto the tips of the tubing module. 4. Insert the tube module into the installation box. Be careful not to disconnect the temperature sensor connector from the tube module. 5. Attach the temperature sensor design to the installation box

Module operation

Module configuration

The module is operated, set up and diagnosed from the Mosaic development environment.

Commissioning

The module is ready for operation after connecting the CIB supply voltage. HW address of the relevant module is indicated on the type plate.

Maintenance

Description

The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected.

Notice

Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!

Warranty

Generally

Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.

Notice

You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.