C-IT-0100H-P Модуль CIB, контактный датчик температуры 30 +120 °C, IP65

The C-IT-0100H-P module is a temperature sensor -50 ° C to + 250 ° C with IP65 protection, which can be connected directly to the CIB wiring bus. The main Pt1000 temperature sensor is in the stem. The information sensor measures the temperature inside the head. The resistance is measured and converted directly in the module to a numerical temperature value. The values are communicated to the basic module via the CIB Common Installation Bus ® . The module thus eliminates measurement errors when connecting external sensors over long distances to common analog inputs.

DI
DI/AI
DO
AI
AO
COM	1x CIB
SENSOR	1x Temperature in the stem 1x Internal temperature in the head

COM - System buses
CIB - Common Installation Bus (R): Installation I/O bus	1x CIB slave
Solar radiation sensor parameters
Solar radiation - measurement range	0 to 1500 W/m²
DI - Organization of binary inputs
Total number of binary inputs	3
Number of groups of binary inputs	1
Organization of binary inputs into groups	3x DI (DI/AI1 - DI/AI3)
DI - Parameters of binary inputs DC (group A)
Parameters valid for inputs on the terminals	3x DI/AI1 - DI/AI3
Number of inputs in group	3
Common wire	GND - module ground
Combined input type	DI/AI Active, for sensing potential-free contacts and measuring resistance sensors
Galvanic isolation of inputs from internal/peripheral circuits	No
Delay from log. 0 to log. 1	200 μs
Delay from log. 1 to log. 0	200 μs
Max. measuring voltage on the connected contact	3,5 V DC
Internal input resistance	2 kΩ
Max. resistance for closed contact, log. 1	< 0,5 kΩ
Min. resistance for open contact, log. 0	> 4,7 kΩ
Anemometer mode	Input DI/AI1 0 - 2000 Hz
AI - Organization of analog inputs
Total number of analog inputs	3
Number of inputs per group	3
Number of analog input groups	1
Organization of analog inputs into groups	3x DI (DI/AI1 - DI/AI3)
Input type	AI / DI - combined
Common wire	GND terminal
Galvanic separation from internal circuits	No
Diagnostics	overload signaling in status word
Digital resolution	12 bit
AI - Analog Input Ranges
Parameters valid for inputs on the terminals	DI/AI1 - DI/AI3
Voltage	0-2 V
Passive sensor	NTC Thermistor 12k / 25 °C (-40 to + 125 °C)
Power supply
Supply voltage, tolerances	24/27 V DC from CIB bus
Power supply from CIB - maximum current consumption (mA)	9 mA
Size and weight
Weight approx.	140 g
Product dimensions (width x height x depth)	65 × 100 × 40 mm
Operating conditions, product standards
Product standard	ČSN EN 60730-1 ed.4 :2017 (EN 60730-1:2016) -Automatic electronic control device (for household and similar purposes)
Protection class of electrical object	III, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP65
Operating areas	Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution	2, according to ČSN EN 61131-2
Overvoltage category installation	III, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device	Outdoor
Working position	Vertical (grommets down)
Ambient operating temperatures	–25 °C až +75 °C
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 ° C to + 85 ° C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	ČSN EN 55022 ed2:2007 (mod CISPR22:2005)
Electromagnetic compatibility / Immunity	min. according to ČSN EN 60730-1 ed.2: 2001
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	The module is packed in a cardboard box. The outer packaging is carried out according to the scope of the order and the method of transport in a transport container provided with labels and other information necessary for transport. Transport from the manufacturer is carried out in the manner agreed upon when ordering. Transport of the product by the customer's own means must be carried out by covered means of transport, in the position specified by the label on the packaging. The box must be stored in such a way as to prevent spontaneous movement and damage to the outer packaging. The product must not be exposed to direct weather conditions during transport and storage. The product is only allowed to be stored in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20°C
Installation
Assembly description	The module is mounted vertically on the support surface with the cable gland facing downwards. The assembly (basic module and possibly peripheral modules) is installed according to TXV 004 13.
Connection
Connection of power and system communication	terminal block with spring clamp 0.2-1.5 mm²
Module operation
Module configuration	Module configuration The module is operated, set and diagnosed from the Mosaic development environment. Commissioning The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is listed on the label on the module. Module diagnostics Basic diagnostics are performed internally and the result is available in the relevant registers of the Mosaic environment.
Maintenance
Description	The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.