C-RQ-0400I-10 Модуль CIB, датчик температуры и влажности, 2×AI/DI, IP54, кабель 1,0 м

Relative humidity and temperature measurement module. It connects a relative humidity and temperature sensor to the CIB bus (the design of the sensor is determined by the part number). It also allows you to connect two universal inputs that can be used separately as binary or analog. The module is designed for measuring relative humidity and air temperature without aggressive additives indoors, exteriors and in ventilation ducts. It is built into an installation plastic box, which is equipped with two plastic bushings for a cable with a diameter of 4.5 ÷ 7 mm provided with removable plugs. The design of the module guarantees the degree of protection IP 54.

DI
DI/AI	2x DI/AI
DO
AI
AO
COM	1x CIB slave
SENSOR	1x Temperature 1x Relative humidity

COM - System buses
CIB - Common Installation Bus (R): Installation I/O bus	1x CIB slave
Parameter des Temperatursensors
Temperature - Description of measurements	AI1 - Pt1000 temperature sensor in the stem for primary temperature measurement in the range -50 to + 200 ° C - Resolution 0.1 ° C - Measurement accuracy 0.5 °C AI2 - temperature measurement inside the head for information on operating conditions of the module (-25 to + 80 ° C). The temperature stabilization time is about 30 minutes
Temperature - Sensor type	Pt1000
Temperature - Measurement range	–50 °C ÷ + 200 °C
Temperature - Resolution	0,1 °C
Temperature - Measurement accuracy	typ. ±0,5 °C
Temperature - Settling time	30 min.
Power supply
Power supply from CIB - voltage	24/27 V DC
Typical power input	0,2 W
Maximum power input	0,3 W
Power supply from CIB - maximum current consumption (mA)	12 mA
Power supply from CIB - Galvanic separation of power supply from internal circuits	No
Power supply from CIB - internal protection	No
Size and weight
Weight approx.	150 g
Product dimensions (width x height x depth)	max. 90 x 66 x 155 mm
Operating conditions, product standards
Product standard	ČSN EN 61131-2: 2005 (idt IEC61131-2: 2003) - Programmable control units
Protection class of electrical object	III, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP65
Operating areas	Normal, according to ČSN 33 2000-3: 1995 (mod IEC 364-3: 1993)
Degree of pollution	1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation	II, acc. ČSN EN 60664-1:2004 (mod IEC 606641:1992)
Type of device	On the wall, in the pit, in the air conditioning, attached
Working position	Any
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	–25 °C o +80 °C
Operating temperature maximum (° C)	+80°C
Operating temperature minimum (° C)	-25°C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	B, according to EN 55022: 1999 (mod CISPR22: 1997)
Electromagnetic compatibility / Immunity	min. as required by EN 61131-2: 2007
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	The module is packed in a paper box. This documentation is also part of the package. The outer packaging is carried out according to the scope of the order and the method of transport in a transport package provided with labels and other data necessary for transport. The product must not be exposed to direct weather conditions during transport and storage. Malting of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C
Installation
Assembly description	The sensor module is mounted in any position using a mounting fitting. The actual temperature sensor, which is located at the end of the stem, should be located so that it is maximally exposed to the measured medium. As a rule, the installation is performed perpendicularly or at an angle of 45 ° to the flow direction of the measured medium. The sensor stem can also be placed in a well, which in undesirable cases protects the sensor from the direct influence of the medium. When mounting and positioning the sensor, it is necessary to ensure that the operating conditions of the head are observed during the subsequent operation of the module. During operation, heat is also transferred along the stainless steel stem of the sensor, so it is necessary to ensure that the temperature is at The stem-head transition did not exceed the permitted head operating temperature.
Connection
Connection description	Sensors with a converter are implemented as standard units on a two-wire CIB bus, which ensures communication and power supply of the entire sensor. The bus wires are connected via a bushing on the terminal board, which is accessible after removing the head cover. Signaling After removing the head cover, it is possible to monitor the status of the module using the indicator LED. If the green indicator LED is lit, the module is connected to the CIB bus. In this case, however, there is no data exchange between the module and the TECOMAT FOXTROT PLC. If the indicator LED flashes, communication between the module and the PLC is faultless.
Connection of power and system communication	terminal block with spring terminal 1.5 mm2, push-in
Module operation
Commissioning	The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module.
Module diagnostics	The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment.
Maintenance
Description	The module does not require any maintenance under general installation conditions.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.