C-RQ-0400H-P-240 Модуль CIB, канальный датчик температуры и влажности, 2×AI/DI, IP54, длина зонда 240 мм

Relative humidity and temperature measurement module. It connects a relative humidity and temperature sensor to the CIB bus (the design of the sensor is determined by the part number). It also allows you to connect two universal inputs that can be used separately as binary or analog. The module is designed for measuring relative humidity and air temperature without aggressive additives indoors, exteriors and in ventilation ducts. It is built into an installation plastic box, which is equipped with two plastic bushings for a cable with a diameter of 4.5 ÷ 7 mm provided with removable plugs. The design of the module guarantees the degree of protection IP 54.

DI
DI/AI	2x DI/AI
DO
AI
AO
COM	1x CIB slave
SENSOR	1x Temperature 1x Relative humidity

AI - Analog Input Ranges (Group A)
Passive sensor	NTC Thermistor 12k / 25 °C (-40 to + 125 °C)
DI: Voltage-free contact	0 when> 1.5 kOhm, 1 when <0.5 kOhm
DI: Balanced resistance input	2x 1k1 (tamper/0/1/tamper)
Resistance measurement error - maximum error at 25 ° C	± 0.5% of full scale
Parameter des Temperatursensors
Temperature - Measurement range	–40 °C ÷ +125 °C
Temperature - Resolution	0,1 °C
Temperature - Measurement accuracy	typ. ±0,3 °C
Humidity sensor parameters
Relative humidity - Measurement range	0 ÷ 100 %RH
Relative humidity - Resolution	1 % RH
Relative humidity - Measurement accuracy	typ. ±2 %RH
Power supply
Power supply from CIB - voltage	24/27 V DC
Power supply from CIB - maximum current consumption (mA)	12 mA
Power supply from CIB - internal protection	Yes, returnable fuse
Size and weight
Weight approx.	200 g
Product dimensions (width x height x depth)	See pictures
Operating conditions, product standards
Product standard	ČSN EN 60730-1 ed. 2:2001 (mod IEC 60730-1:1999)
Protection class of electrical object	III, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP54
Operating areas	Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution	1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation	II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device	Outdoor
Working position	Any
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	-20 °C to + 55 °C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	B, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015)
Electromagnetic compatibility / Immunity	min. according to ČSN EN 60730-1 ed.2: 2001
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	Модуль упакован в антистатический пакет. Эта документация также является частью пакета. Внешняя упаковка осуществляется в соответствии с объемом заказа и способом транспортировки в транспортной упаковке, снабженной этикетками и другими данными, необходимыми для транспортировки. Продукт не должен подвергаться воздействию прямых погодных условий во время транспортировки и хранения. Соложение продукта разрешено только в чистых помещениях. без токопроводящей пыли, агрессивных газов и паров. Наиболее подходящая температура хранения - 20 ° C.
Installation
Assembly description	Individual module variants can be mounted in any position. The dimensions and location of the mounting holes are shown in the following figures. The TXN 133 62.01 and .04 modules are mounted on a level surface. Mounting holes are accessible after removing the box lid. The TXN 133 62.02 and .03 modules are mounted in air ducts, and a plastic sleeve is supplied with them for easier mounting.
Connection
Connection description	The relative humidity and temperature sensor is located in the unscrewable plastic end of the pipe (in variants TXN 133 62.01 to .03), where it is protected by a dust filter, or in a non-removable plastic block (variant TXN 133 62.04) at the end of the cable with a filter preventing the ingress of solid particles. larger than 0.1 μm.
Connection of power and system communication	terminal block with spring terminal 1.5 mm2, push-in
Connection of inputs / outputs	terminal block with spring terminal 1.5 mm2, push-in
Module installation tools	(-) 3 mm, flat screwdriver
Module operation
Commissioning	The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module.
Module diagnostics	The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment.
Maintenance
Description	The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.