C-IR-0202S Модуль CIB, 2×AI/DI (RTD/контакт), 1×AO, реле 3 А

The C-IR-0202S module is a dimensionally minimalist module on the CIB bus for relay contact control or for continuous control via voltage analog output. At the same time, it is intended for connection of two passive temperature sensors or binary signals from contacts and their conversion into data for the CIB wiring bus. - The resistance from the optional Pt1000, Ni1000, NTC 12k, KTY81-121 sensors against the common GND conductor is linearized in the module and converted directly to a numerical temperature value and then transferred to the basic module via the CIB bus. It is possible to choose the measurement of other resistances in the range of 0 to 160 kΩ, but the conversion to temperature and linearization must be performed in the control panel at the level of the application program. - Binary signals are connected to the inputs only as a free contact against the common GND conductor. - The voltage of the analog output 0 - 10 V is connected on the conductor against the common conductor GND. - The output switching contact of the relay is led out by two separate conductors with increased insulation.

DI
DI/AI	2x DI/AI
DO	1x RO (3A)
AI
AO	1x AO (0-10V)
COM	1x CIB slave
SENSOR

COM - System buses
CIB - Common Installation Bus (R): Installation I/O bus	1x CIB slave
DI - Organization of binary inputs
Total number of binary inputs	2
Number of groups of binary inputs	1
Organization of binary inputs into groups	2x DI (DI/AI1, DI/AI2)
DI - Parameters of binary inputs DC (group A)
Parameters valid for inputs on the terminals	DI/AI1, DI/AI2
Number of inputs in group	2
Common wire	GND - module ground
Combined input type	DI/AI Active, for sensing potential-free contacts and measuring resistance sensors
Galvanic isolation of inputs from internal/peripheral circuits	No
Max. measuring voltage on the connected contact	3,3 V DC
Internal input resistance	2 kΩ
Max. resistance for closed contact, log. 1	< 0,5 kΩ
Min. resistance for open contact, log. 0	> 1,5 kΩ
AI - Organization of analog inputs
Total number of analog inputs	2
Number of inputs per group	2
Number of analog input groups	1
Organization of analog inputs into groups	2x AI (DI/AI1, DI/AI2)
Input type	With common clamp
Common wire	GND terminal
Galvanic separation from internal circuits	No
AI - Analog Input Ranges (Group A)
Parameters valid for inputs on the terminals	DI/AI1, DI/AI2
Passive sensor	NTC Thermistor 12k / 25 °C (-40 to + 125 °C)
DI: Voltage-free contact	0 when> 1.5 kOhm, 1 when <0.5 kOhm
DI: Balanced resistance input	2x 1k1 (tamper/0/1/tamper)
Resistance measurement error - maximum error at 25 ° C	± 0.5% of full scale
Power supply
Supply voltage, tolerances	24/27 V DC from CIB bus
Power supply from CIB - typical current consumption (mA)	10 mA
Power supply from CIB - maximum current consumption (mA)	12 mA
Power supply from CIB - Galvanic separation of power supply from internal circuits	No
Power supply from CIB - internal protection	Yes, returnable fuse
Size and weight
Weight approx.	7 g
Product dimensions (width x height x depth)	55 x 26 x 16 mm
Operating conditions, product standards
Product standard	ČSN EN 60730-1 ed. 2:2001 (mod IEC 60730-1:1999)
Protection class of electrical object	I, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP10B
Operating areas	Normal according to ČSN 33 2000-1: 2003 (IEC 364-1: 1992 mod)
Degree of pollution	1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation	II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device	In the installation box, under the cover
Working position	Any
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	0 ° C to + 55 ° C
Operating temperature maximum (° C)	+70°C
Operating temperature minimum (° C)	-25°C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	ČSN EN 55022 ed2:2007 (mod CISPR22:2005)
Electromagnetic compatibility / Immunity	min. according to ČSN EN 60730-1 ed.2: 2001
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	Модуль упакован в антистатический пакет. Эта документация также является частью пакета. Внешняя упаковка осуществляется в соответствии с объемом заказа и способом транспортировки в транспортной упаковке, снабженной этикетками и другими данными, необходимыми для транспортировки. Продукт не должен подвергаться воздействию прямых погодных условий во время транспортировки и хранения. Соложение продукта разрешено только в чистых помещениях. без токопроводящей пыли, агрессивных газов и паров. Наиболее подходящая температура хранения - 20 ° C.
Installation
Assembly description	The module is inserted freely into the installation box or attached with a suitable cable tie inside the device. The supply wires can be separated and shortened as required. However, to prevent interference problems, the active conductors must be routed together with the common GND conductor to the sensor so that no interference loops form between the conductors. Best with twisted pair cables.
Connection
Connection of power and system communication	Ribbon flat conductors 0.15 / 0.5 mm2
Module connection	Sensors with a converter are implemented as standard units on a two-wire CIB bus, which ensures communication and power supply of the entire sensor. For more information, see the Peripheral Modules on the CIB TXV 004 13 manual. An example of the module connection is shown in the following figure.
Module operation
Commissioning	The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module.
Module diagnostics	The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment.
Maintenance
Description	The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.