C-IR-0203S-16A Модуль CIB, 2×AI/DI (температура/контакт), 2×AO, реле 16 А

C-IR-0203S is a module designed for connection to the CIB bus. Contains - two combined analog or binary inputs - two analog outputs with a range of 0-10 V - one relay output with changeover contact. Inputs and analog outputs are connected to the terminal block with pen terminals, the relay output to the terminal block with screw cage terminals. - The inputs allow direct connection of resistance sensors PT1000, Ni1000, sensor with thermistor NTC12k or KTY81-121 against a common GND wire. The resistance is converted in the module directly to a numerical temperature value. - For another type of resistance sensor, resistance measurement in the range 0-160 kΩ can be selected, but the conversion to temperature and linearization must be performed only at the level of the user program. - The binary signals are connected to the inputs only as a free potential-free contact against the common conductor GND, or the input can operate in balanced input mode. - The 0-10 V analog outputs are connected to a common GND conductor.

DI
DI/AI	2x DI/AI
DO	1x RO (16A)
AI
AO	2x AO
COM	1x CIB slave
SENSOR

COM - System buses
CIB - Common Installation Bus (R): Installation I/O bus	1x CIB slave
DI - Organization of binary inputs
Total number of binary inputs	5
Number of groups of binary inputs	2
Organization of binary inputs into groups	4x DI (DI/AI1 - DI/AI4) 1x DI (DI/AI5)
DI - Parameters of binary inputs DC
Parameters valid for inputs on the terminals	DI/AI1 - DI/AI5
Common wire	GND - module ground
Combined input type	DI/AI Active, for sensing potential-free contacts and measuring resistance sensors
Galvanic isolation of inputs from internal/peripheral circuits	No
Galvanic separation of inputs from CIB bus	No
Internal input resistance	2 kΩ
Max. resistance for closed contact, log. 1	< 0,5 kΩ
Min. resistance for open contact, log. 0	≥ 2,7 kΩ
Balanced resistance input	2× 1k1 (tamper/0/1/tamper)
AI - Organization of analog inputs
Total number of analog inputs	5
Number of analog input groups	2
Organization of analog inputs into groups	4x DI (DI/AI1 - DI/AI4) 1x DI (DI/AI5)
Input type	4x DI (DI/AI1 - DI/AI4) 1x DI (DI/AI5)
Common wire	GND terminal
Galvanic separation from internal circuits	No
Galvanic isolation of the inputs from each other	No
AI - Analog Input Ranges
Passive sensor	NTC Thermistor 12k / 25 °C (-40 to + 125 °C)
Input impedance in signal range RTD	2,0 kΩ
Resistance measurement error - maximum error at 25 ° C	±0.5% of full scale, ±2% of value
AO - Analog output parameters
The number of groups of analogue outputs	1
Number of outputs in group	4
Number of outputs and their organization into groups	4x AO (AO1-AO4)
Common wire of group	GND terminal
Galvanic isolation from internal circuits	No
Output type	active voltage output
Voltage output - voltage	0 - 10 V
Voltage output - Resolution 1 LSB	10,546 mV
Voltage output - Adjustable range	0 ÷ 125 % Ujm
Voltage output - Load resistance	>1 kΩ
Voltage output - Load capacity	250 nF
Voltage output - maximum output current	10 mA
Voltage output - Maximum output current for the group	15 mA
Power supply
Supply voltage, tolerances	24/27 V DC from CIB bus
Power supply from CIB - maximum current consumption (mA)	42 mA
Size and weight
Weight approx.	7 g
Product dimensions (width x height x depth)	55 × 26 × 20 mm
Operating conditions, product standards
Product standard	ČSN EN 60730-1 ed.4 :2017 (EN 60730-1:2016) -Automatic electronic control device (for household and similar purposes)
Protection class of electrical object	III, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP10B
Operating areas	Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution	1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation	II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device	In the installation box, under the cover
Working position	Any
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	0 ° C to + 70 ° C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 ° C to + 85 ° C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	ČSN EN 55022 ed2:2007 (mod CISPR22:2005)
Electromagnetic compatibility / Immunity	min. according to ČSN EN 60730-1 ed.2: 2001
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	Модуль упакован в антистатический пакет. Эта документация также является частью пакета. Внешняя упаковка осуществляется в соответствии с объемом заказа и способом транспортировки в транспортной упаковке, снабженной этикетками и другими данными, необходимыми для транспортировки. Продукт не должен подвергаться воздействию прямых погодных условий во время транспортировки и хранения. Соложение продукта разрешено только в чистых помещениях. без токопроводящей пыли, агрессивных газов и паров. Наиболее подходящая температура хранения - 20 ° C.
Connection
Connection description	An example of module connection is shown in the following figure.
Connection of power and system communication	terminal block with spring terminal 0.15-0.5 mm2, push-in
Connection of inputs / outputs	terminal block with spring clamp 0.15-0.5 mm2, push-in
Module operation
Module configuration	The module is operated, set up and diagnosed from the Mosaic development environment.
Commissioning	The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module.
Module diagnostics	The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment.
Maintenance
Description	The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.