CF-2142 CIB Master, 2 шины CIB, Ethernet, до 64 подчиненных устройств

CF-2141; Single-channel external CIB bus master, communication with CP-Ethernet

DI
DI/AI
DO
AI
AO
COM	1x ETH 1x CIB master
SENSOR

COM - System buses
CIB - Common Installation Bus (R): Installation I/O bus	1x CIB slave
COM - Wireless network
RFox2 wireless network	RFox2 Master
RFox2 wireless network range	up to 256 RFox2 slave nodes
Communication frequency band	868,1 MHz
Transmission power	+14 dBm
Input sensitivity	–108 dBm
Modulation type	2-GFSK
Communication speed	50 kbps
Power supply
Power supply from CIB - voltage	24/27 V DC
Maximum power input	< 0,5 W
Module thermal/power loss	0,4 W
Internal protection	Yes, PTC reversible fuse
Size and weight
Weight approx.	50 g
Module width in multiples of M (17.5 mm)	1M
Product dimensions (width x height x depth)	22,7 x 95 x 58 mm
Operating conditions, product standards
Product standard	ČSN EN 60730-1 ed. 3:2012 (mod IEC 60730-1:2010)
Protection class of electrical object	II, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP20
Operating areas	Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution	1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation	II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device	Module on DIN rail
Working position	Vertical
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	-20 °C to + 55 °C
Operating temperature maximum (° C)	+55°C
Operating temperature minimum (° C)	-20°C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	B, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015)
Emmisions - note	In premises where the use of radio and television receivers can be expected to be used a distance of 10 m from these devices may cause radio interference. In such a case, the user may be required to take appropriate action.
Electromagnetic compatibility / Immunity	min. according to ČSN EN 60730-1 ed.3: 2012
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Connection
Connection description	An example of module connection is shown in the following figure. Any type designed for the 868 MHz band can be used as an antenna by terminating with an SMA connector (pin).
Connection of power and system communication	terminal block with screw terminal 2.5 mm2
Module operation
Module configuration	The module is operated in the RFox2 radio network as a peripheral module, the settings are made using the IO Configurator tool in the Mosaic programming environment, see the TXV 003 93 manual in the RFox2Lib description.
Module diagnostics	The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment.
Maintenance
Description	The module does not require any maintenance under general installation conditions.
Warning	Because the module contains semiconductor components, it is necessary to follow the principles for working with components sensitive to electrostatic charges during handling. Repairs are performed exclusively by the manufacturer's service center or the manufacturer's authorized service.
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.