SpeedyBee Adapter 3 tdi

Доставка в течение 2–3 недель. SPEEDYBEE ADAPTER 3 NO LAPTOP, NO POWER BANK, AND NO LIPO CHECKER IN YOUR FPV BAG. Turn your smartphone into your mobile FPV companion Connect to the SpeedyBee mobile app, and configure your flight controller anytime, anywhere. Or flash the latest version of Betaflight/Emuflight/INAV in just 2 minutes before your flight session. The choice is yours. Analyzing Blackbox data has never been easier No laptop, no separate app, no hassle. Connect your quad to the SpeedyBee mobile app and analyze your Blackbox data* in just 1.5 minutes after a flight. Get the most out of your practice sessions now. *Currently supports Betaflight and Emuflight only Your LiPo batteries = Powerful 30W power banks Connect SpeedyBee Adapter 3 to a LiPo battery and charge your mobile phone* and tablets when you need them the most. Supports mainstream QC3.0/AFC/Apple 2.4A (iPhone 6s and above) and other fast charging protocols with charging power up to 30W. Complete with over-current protection, short-circuit protection and over-temperature protection to protect your gadgets from unwanted accidents. Phone Model Battery Capacity Battery level after half an hour of charging Mi 11 Ultra 5000mAh 52% Samsung S10 3400mAh 49% HUAWEI P40 Pro 4400mAh 45% iPhone 11 3110mAh 22% *Charging function requires 2S LiPo and above. Forgot your LiPo checker? Worry not Connect your 1S - 6S LiPo and the display will immediately show your battery voltage and the remaining power with a specific colour code*. The built-in beeper will alert you if the remaining power is less than 40% to help extend your battery lifespan. *GREEN(>80%), WHITE(40-80%) and RED(<40%). MicroUSB or Type C? Why not both? SpeedyBee Adapter 3 comes with a dual-head data cable, with MicroUSB 2.0 and USB 3.0 Type C connector on each end. No more worries about connector compatibility regardless of what flight controller you are using in your build. WiFi + Bluetooth = the best of both worlds Use Bluetooth for quick access to your firmware configurator, or switch to Wi-Fi to flash firmware or download Blackbox data at a higher speed. And all you need is just one LiPo Access the configurator function using any LiPo batteries available to you. Supports all 1S - 6S LiPo with PH2.0 or XT60 connectors. Plug in that beefy 6S 1500mah, or that tiny 1S Whoop battery (minimum voltage 3.8V), to the SpeedyBee Adapter 3 you are ready to access the configurator. Specifications Product Name SpeedyBee Adapter 3 Power Input Voltage Range 1-6S(3.8V+ for 1S) Power Input Connector XT60-Male, PH2.0 male Required Mobile Device System Version Android 7.0+ | iOS 12.0+ Supported SpeedyBee App Version V1.6.1 + for iOS | V1.5.6+ for Android Supports Firmware Configurators and Flashing: • Betaflight 3.2.0 and above • iNAV 2.0.0 and above • EmuFlight 0.1.0 and above Flashing only, excludes Configurators: • Ardupilot Wireless signal transmission frequency • Bluetooth frequency: 2402 - 2480 MHz • WiFi frequency: 2412 - 2484 MHz Maximum Output Current for flight controllers 700mA @5V Fast Charging Output interface USB A Port Minimum Input Voltage for Charging output 7.4V(2S LiPo) Supported Fast Charging Protocol • QC3.0/QC2.0 • AFC • FCP • SCP/High SCP • PE2.0/PE1.1 • SFCP Max Fast Charging Current 3.5A Max Fast Charging Power 30W Case Material ABS + PC Liquid Silicone Cable Length 12.4cm Dimension(Main Body) 24.8*21.8*53.6mm Net Weight 35g Package 1 x Adapter 3 1 x Manual Card SpeedyBee Adapter 3 VS SpeedyBee Adapter 2 VS OTG Item SpeedyBee Adapter 3 SpeedyBee Adapter 2 OTG Support 1-6S LiPo input ✔ ✔ N/A XT60 and PH2.0 connectors ✔ ✔ N/A BF/INAV/EMU configuration ✔ ✔ ✔ Flight control firmware upgrade ✔ ✔ ✘ Built-in WiFi ✔ ✔ ✘ Built-in Bluetooth ✔ ✘ ✘ Blackbox downloader and analyzer ✔ ✘ ✘ Built-in MicroUSB and Type C connector ✔ ✘ ✘ Fast charging output up to 30W ✔ ✘ ✘ Built-In LiPo Voltage Checker ✔ ✘ ✘