C-IT-0200I-SI Модуль CIB, датчик сонячного випромінювання 0 1500 Вт/м², IP65

Solar radiation measurement module with IP65 protection for outdoor installation. It is used to evaluate the incident energy in the range of 0-1500W / m2. For the measurement, it uses a monocrystalline silicon cell with an integrated temperature sensor for temperature compensation of the measured value. To accurately calculate the intensity in W / m2, enter the individual calibration constant listed on the inside of the lid.

DI
DI/AI
DO
AI
AO
COM
SENSOR

COM - System buses
CIB - Common Installation Bus (R): Installation I/O bus	1x CIB slave
DI - Parameters of binary inputs DC (group A)
Parameters valid for inputs on the terminals	AI1-AI5
Common wire	GND - module ground
Combined input type	Active / passive binary input; Active when setting the range 0-10V. Passive when setting the Pt1000, Ni1000 and KTY81-121 ranges.
Galvanic isolation of inputs from internal/peripheral circuits	No
Input current at log. 1 (typ.)	1,5 mA typ.
Delay from log. 0 to log. 1	10 ms
Delay from log. 1 to log. 0	300 ms
The minimum width of the captured pulse	30 ms
Internal input resistance	64,9 kΩ
Notice	1) Input AI5 has a reduced voltage supply for the binary counter, which does not correspond to the S0 interface standard. 2) Digital inputs do not have their own configuration. The type of digital input can thus be selected using the appropriate analog range. 3) The type of digital input is set using the corresponding analog range when configuring the module in the Mosaic environment. The active digital input corresponds to the range 0 ÷ 10 V. The passive digital input corresponds to the ranges Pt1000, Ni1000, KTY81-121.
Pulse counter
Reference voltage (1)	for inputs AI1 - AI4: Typically 24 V DC (according to CIB supply voltage)
Reference voltage (2)	for AI5 input Typically 7.4 V DC
Maximum input current	14 mA
Pulse length	≥ 30 ms
Maximum frequency	20 Hz
Maximum resistance of the switch in the closed state	800 Ω
AI - Organization of analog inputs
Number of inputs per group	5
Number of analog input groups	1
AI - Analog Input Ranges (Group A)
Parameters valid for inputs on the terminals	AI1- AI5
Voltage	0 -1 V
Voltage input error - max. error at 25 ° C	± 2.0% of full scale
Voltage input error - temperature coefficient	± 0,1% of full scale
Voltage input error - non-linearity	± 0.1% of full scale
Voltage input error - repeatability under steady state conditions	0.5% of full scale
Ccurrent	0 - 20 mA
Current	4-20 mA
Current input error - maximum error at 25 ° C	±2% of full scale
Error current input - temperature coefficient	± 0,1% of full scale
Error current input - nonlinearity	± 0,1% of full scale
Error current input - repeatability at steady-state conditions	0.5% of full scale
Passive sensor	NTC Thermistor 12k / 25 °C (-40 to + 125 °C)
Resistance measurement error - maximum error at 25 ° C	± 2% of full scale
Resistance measurement error - temperature coefficient	± 0,1% of full scale
Resistance measurement error - non-linearity	± 0.1% of full scale
Resistance measurement error - repeatability at steady conditions	0.5% of full scale
Flowmeter interface parameters
Parameters valid for terminals	AV23
Type of flow meter to connect	TacoSetter Tronic
Principle of flow measurement	Vortex in the medium
Integrated power supply for the flow meter	Yes - from CIB power supply
Flow meter supply voltage	5 V DC
Typical consumption from CIB	3 mA
Input for flow meter - input resistance	> 14 kΩ
Input for flow meter - measuring range	0,5 ÷ 3,5 V
Input for flow meter - error of measuring input	0,50 %
Integrated thermometer input - input resistance	> 14 kΩ
Integrated thermometer input - measuring range	0,5 ÷ 3,5 V
Integrated thermometer input - measuring input error	0,50 %
Power supply
Supply voltage, tolerances	24/27 V DC from CIB bus
Power supply from CIB - typical current consumption (mA)	40 mA
Power supply from CIB - maximum current consumption (mA)	80 mA
Internal protection	No
Size and weight
Weight approx.	70 g
Product dimensions (width x height x depth)	85 x 85 x 37 mm
Operating conditions, product standards
Product standard	ČSN EN 60730-1 ed. 2:2001 (mod IEC 60730-1:1999)
Protection class of electrical object	I, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP 55
Operating areas	Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution	1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation	II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device	On the wall
Working position	Any
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	-10 °C to + 55 °C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	B, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015)
Electromagnetic compatibility / Immunity	min. according to ČSN EN 60730-1 ed.2: 2001
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	The module is packed in a paper box. This documentation is also part of the package. The outer packaging is carried out according to the scope of the order and the method of transport in a transport package provided with labels and other data necessary for transport. The product must not be exposed to direct weather conditions during transport and storage. Malting of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C
Installation
Assembly description	Indoor wall mounting
Connection
Connection of power and system communication	terminal block with spring terminal 1.5 mm2, push-in
Connection of inputs / outputs	terminal block with spring terminal 1.5 mm2, push-in
Specific I / O	TacoSetter Tronic flowmeter
Module installation tools	(-) 3 mm, flat screwdriver
Module connection	The module is implemented as a CIB bus module, which provides communication. The power supply of the module is from an external source. The CIB bus can have any topology and branching up to a distance of 500 m and up to 32 units on one CIB branch. The CIB bus master is Foxtrot base unit or external master, such as the CF-1141 module. Further information can be found in the manual Peripheral modules on the CIB TXV 004 13. An example of module connection is shown in the following figure.
Module operation
Module configuration	The C-AM-0600I module allows the measurement of temperature, voltage, current, resistance and the number of pulses. The measuring range is selected using the module configuration menu in the Mosaic environment or possibly in another configuration SW
Commissioning	The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module.
Module diagnostics	The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment.
Maintenance
Description	The module does not require any maintenance under general installation conditions.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.